Skip to main content

Posts

What is SNMP

An SNMP-managed network consists of three key components:   1)     Managed device   2)     Agent — software which runs on managed devices   3)     Network management station (NMS) — software which runs on the manager The SNMP agent receives requests on UDP port 161. The manager may send requests from any available source port to port 161 in the agent. The agent response will be sent back to the source port on the manager. The manager receives notifications ( Traps  and  InformRequests ) on port 162. The agent may generate notifications from any available port. When used with  Transport Layer Security  or  Datagram Transport Layer Security  requests are received on port 10161 and traps are sent to port 10162. •       UDP port 161 used for polling •       UDP port ...

Non overlapping channels:

Channels that wont overlap for example, in 5.8 GHzc50 MHz spectrum available, 5825 to 5875, in 20 MHz channel bandwidth there are 2 non-overlapping channels are available.  5835MHz (5825 to 5845),  5855MHz(5845 to 5865). 3 non-overlapping channels in 2.4GHz(channels 1,6&11) India unlicensed band 2.4 - 2.4835GHz. 5.825-5.875GHz Power: Maximum transmitter output power of 1 Watt ( 4 Watts Effective Radiated Power) (30 dbm) in spread of 10 MHz or higher. 4 Watt peak or 36 dbm EIRP: Equivalent/ Effective isotropic radiated power=36dbm/indoor 16dBm): EIRP=Tx Power(dBm)+Antenna gain (dBi)-cable loss

RSSI/SNR/Fade Margin

RSSI: RSSI is the receiver signal strength indicator, RSSI is usually a negative value; the closer to 0, the better. unit dBm. SNR Signal to Noise ratio: SNR is signal strength, relative to noise level. The higher the SNR, the better. Unit dB. Fade margin: It’s calculated from Received rssi level vs threshold rssi level. Unit dB (+ve value). Higher the value meant by good signal strength.

VLAN: 802.1q:

Logical network. A single layer 2 network portioned to create multiple broadcast domains. Which are mutually isolated, 4095 vlans (0 to 4095 are reserved). 32 bit will added to the Ethernet frame b/w source mac and etherType. It reduce the broadcasting by increasing the broadcasting domain. 16 bits 3 bits 1 bit 12 bits TPID TCI PCP DEI VID ·          Tag protocol identifier (TPID) : a 16-bit field set to a value of 0x8100 in order to identify the frame as an IEEE 802.1Q-tagged frame. This field is located at the same position as the EtherType/length field in untagged frames, and is thus used to distinguish the frame from untagged frames. ·          Tag control information (TCI) ·          Priority code point (PCP) : a 3-bit field which refers to the   IEEE 802.1p   class...

SSID/BSSID/BSS and SSID hiding

SSID( service set identifier) ASSCI string : A series of 0 to 32 octets, Network name, Unique identifier for a wireless LAN. BSS(Basis service set): a single AP together with all associated clients(STAs) is called a BSS. Each BSS is uniquely identified by a   basic service set identification   (BSSID) BSSID(Basis service set identifier): the BSSID is the MAC address   of the   AP generated by combining the 24 bit Organization Unique Identifier (the manufacturer's identity) and the manufacturer's assigned 24-bit identifier. ESS(Extended Service set): each BSS still has its BSSID, however, the entire ESS uses only one SSID ( to facilitate roaming), BSSID is a locally administered MAC address generated from a 48-bit random number. Hiding SSID: AP will not broadcast the SSID, this feature is to prevent unauthorized users from being able to detect the wireless network from their wireless clients. APs send beacon frames to advertise capability i...

WDS (Wireless Distribution system)

To establish a distributed WLAN, two or more access points are configured with the same service set identifier ( SSID ). Access points configured with the same SSID make up a single  logical network  within a single  Layer 2 broadcast domain, which means that they must all be able to communicate. The most common use of a wireless distribution system is to bridge a WLAN spanning two buildings. The simplest WDS consists of two access points configured to forward messages to each other. WDS may provide two modes of access point-to-access point (AP-to-AP) connectivity: ·          Wireless bridging , in which WDS APs (AP-to-AP) communicate only with each other and don't allow wireless stations (STA) (also known as wireless clients) to access them ·          Wireless repeating , in which APs communicate with each other and with wireless STAs

WPS (Wi-Fi Protected Setup)

WPS: Wi-Fi Protected Setup (WPS) is the industry standard method to simplify the security setup of Wi-Fi networks. You now can easily setup and connect to a WPA-enabled 802.11 network with WPS-certificated devices using either Personal Information Number (PIN) or Push Button Configuration (PBC) or NFC. Push button method : in which the user has to push a button, on both the access point and the new wireless client device. Support of this mode is mandatory for access points and optional for connecting devices. PIN entry : in all Wi-Fi Protected Setup networks, a unique PIN (Personal Identification Number) will be required for each device to join the network.  A fixed PIN label or sticker may be placed on a device, or a dynamic PIN can be generated and shown on the device's display (e.g., a TV screen or monitor).  PIN is used to make sure the intended device is added to the network being set up and will help to avoid accidental or malicious attempts to add unintende...